100W 12V RV Solar Wiring Diagram Printable (1S1P)
Computed 100W 12V rv / camper solar diagram: 1S1P array, wire gauges, OCPD, battery arrangement, routed parts and printable files.
View the scalable diagram inline
What this computed plan shows
The 100W 12V RV Solar Wiring Diagram Printable (1S1P) turns a searched-for rv / camper idea into one internally consistent DC schematic. Its 100 W array uses 1 modules in 1S1P, so the drawing labels the array at 20 Vmp and 5.5 Isc rather than relying on a generic icon. The result is a planning reference for comparing real equipment ratings before installation.
Controller sizing follows two separate limits in this rv / camper configuration. Power conversion calls for 11 A or more at the battery side, and cold-array allowance raises the PV check from 24 V nameplate Voc to 30 V. The selected MPPT envelope is 30 A and 100 V.
Conductor results change from one section of the 100W 12V RV Solar Wiring Diagram Printable (1S1P) to the next. Across 47 ft, the PV side selects 6 AWG copper at 1.98% drop; across 9 ft, the charging side selects 12 AWG copper at 2.48%. Their respective 15 A and 15 A devices are listed separately so one rating is never copied into the other circuit.
For storage, the computed arrangement is 1S3P, assembled from 3 × 200 Ah AGM batteries. Series connection establishes the 12 V nominal level, while parallel strings bring the bank to 600 Ah. The displayed 7,200 Wh is nominal capacity rather than a promise of daily usable energy.
The inverter contributes 55.6 A of continuous DC input at the engine’s efficiency assumption. Over a 2 ft one-way cable path, 4 AWG copper and a 70 A protective device keep calculated drop at 0.57%. Its 1,200 W surge label is recorded for equipment comparison, but the schedule must still be checked against the chosen inverter manual.
This page stays inside the verified engine boundary: every component and conductor currently returns a within verdict. A different panel label, longer run, hotter ambient or changed battery count can alter that result, so follow the customize link rather than scaling the picture by intuition. Local rules, equipment listings and inspection requirements take precedence over this planning aid.
For later comparison, keep the 100 W array, 1S3P bank and the 47/9/2 ft one-way routes together when requesting equipment quotes or an inspection review.
Wire, protection and battery schedules
Wire schedule
| Segment | Design current | One-way run | Computed conductor | Voltage drop | Sizing basis |
|---|---|---|---|---|---|
| array → controller | 8.6 A | 47 ft | 6 AWG copper | 1.98% | 156% of array Isc (NEC 690.8) |
| controller → battery | 8.3 A | 9 ft | 12 AWG copper | 2.48% | controller output at 125% continuous-load ampacity |
| battery → inverter | 55.6 A | 2 ft | 4 AWG copper | 0.57% | inverter continuous DC input at 90% efficiency and 125% ampacity |
Overcurrent protection
| Protected segment | Required ampacity | OCPD | Conductor ampacity | Verdict |
|---|---|---|---|---|
| array → controller | 8.6 A | 15 A | 55 A | within |
| controller → battery | 10.4 A | 15 A | 20 A | within |
| battery → inverter | 69.4 A | 70 A | 70 A | within |
Battery arrangement
| Arrangement | Chemistry | Units | Unit capacity | Bank capacity | Nominal energy | Nominal voltage |
|---|---|---|---|---|---|---|
| 1S3P | AGM | 3 | 200 Ah | 600 Ah | 7,200 Wh | 12 V |
Static routed parts list
Parts are computed from this passing configuration. A route appears only when the verified catalogue record proves every displayed numeric rating; all uncertain matches stay local for verification. Routed links may earn Off Grid Authority a commission at no extra cost to you.
Pre-install review steps
- Confirm the array and controller window: Verify that the 1S1P string plan produces 24 V open circuit and that the equipment is rated above the 30 V cold-design value.
- Lay out the protected DC runs: Measure the one-way paths before ordering cable, then compare them with the computed 47 ft, 9 ft and 2 ft runs shown here.
- Build complete battery strings: Arrange all 3 battery units as 1S3P; do not leave a partial series string in a 12 V bank.
- Commission against equipment instructions: Check polarity, terminal torque, DC interrupt ratings, conductor temperature ratings, ambient correction and local inspection requirements before energizing the 600 W inverter.
Customize or compare
Open the parent build guide for the surrounding design context, safety notes and installation discussion.