3200W 24V Garage Solar Wiring Diagram with Battery (4S2P)
Computed 3200W 24V garage solar diagram: 4S2P array, wire gauges, OCPD, battery arrangement, routed parts and printable files.
View the scalable diagram inline
What this computed plan shows
For the 3200W 24V Garage Solar Wiring Diagram with Battery (4S2P), a 4S2P array gives 3,200 W of rated panel capacity for the garage use case. Nameplate multiplication produces 198 Voc, 164 Vmp and 20.4 Isc at the combined array. Those values are carried forward into controller and conductor checks instead of being rounded into a one-size-fits-all diagram.
The MPPT controller needs at least 167 A of output capacity. Its PV input must also remain above the engine’s 247.5 V cold-design check, while the configured ceiling is 300 V. That margin matters because the diagram’s 198 V nameplate value is not the final controller comparison value.
The array-to-controller route is 31 ft one way and carries 31.8 design amps. It resolves to 8 AWG copper, a 35 A OCPD and 0.94% calculated drop. Downstream, the 10 ft controller lead uses 4/0 AWG copper behind 175 A protection, holding its computed drop to 0.68%.
A 2S2P layout keeps every battery in a complete 24 V string. Using 4 LiFePO₄ units at 120 Ah each yields 240 bank amp-hours and 6,144 nominal watt-hours. Parallel paths still need equal cable geometry, suitable disconnecting means and manufacturer-approved protection.
The battery-to-inverter path is only 4 ft, but it carries 122.7 A continuously in the calculation. That combination selects 4/0 AWG copper and 175 A protection while retaining 0.25% drop. The 5,300 W surge figure should be compared with motor or compressor starting loads separately from continuous power.
Use the parts links as a routed specification checklist, not permission to substitute unlike ratings. Before buying, confirm controller voltage, breaker interrupt rating, conductor insulation, terminal temperature class, battery series approval and inverter DC range. The customizer carries this exact 3200W 24V Garage Solar Wiring Diagram with Battery (4S2P) state in its URL hash so run lengths or nameplate values can be changed without editing the static drawing.
For later comparison, keep the 3,200 W array, 2S2P bank and the 31/10/4 ft one-way routes together when requesting equipment quotes or an inspection review.
Wire, protection and battery schedules
Wire schedule
| Segment | Design current | One-way run | Computed conductor | Voltage drop | Sizing basis |
|---|---|---|---|---|---|
| array → controller | 31.8 A | 31 ft | 8 AWG copper | 0.94% | 156% of array Isc (NEC 690.8) |
| controller → battery | 133.3 A | 10 ft | 4/0 AWG copper | 0.68% | controller output at 125% continuous-load ampacity |
| battery → inverter | 122.7 A | 4 ft | 4/0 AWG copper | 0.25% | inverter continuous DC input at 90% efficiency and 125% ampacity |
Overcurrent protection
| Protected segment | Required ampacity | OCPD | Conductor ampacity | Verdict |
|---|---|---|---|---|
| array → controller | 31.8 A | 35 A | 40 A | within |
| controller → battery | 166.7 A | 175 A | 195 A | within |
| battery → inverter | 153.4 A | 175 A | 195 A | within |
Battery arrangement
| Arrangement | Chemistry | Units | Unit capacity | Bank capacity | Nominal energy | Nominal voltage |
|---|---|---|---|---|---|---|
| 2S2P | LiFePO₄ | 4 | 120 Ah | 240 Ah | 6,144 Wh | 24 V |
Static routed parts list
Parts are computed from this passing configuration. A route appears only when the verified catalogue record proves every displayed numeric rating; all uncertain matches stay local for verification. Routed links may earn Off Grid Authority a commission at no extra cost to you.
Pre-install review steps
- Confirm the array and controller window: Verify that the 4S2P string plan produces 198 V open circuit and that the equipment is rated above the 247.5 V cold-design value.
- Lay out the protected DC runs: Measure the one-way paths before ordering cable, then compare them with the computed 31 ft, 10 ft and 4 ft runs shown here.
- Build complete battery strings: Arrange all 4 battery units as 2S2P; do not leave a partial series string in a 24 V bank.
- Commission against equipment instructions: Check polarity, terminal torque, DC interrupt ratings, conductor temperature ratings, ambient correction and local inspection requirements before energizing the 2,650 W inverter.
Customize or compare
Open the parent build guide for the surrounding design context, safety notes and installation discussion.