5kW 48V Tiny Home Solar Wiring Diagram Printable (5S2P)
Computed 5kW 48V tiny home solar diagram: 5S2P array, wire gauges, OCPD, battery arrangement, routed parts and printable files.
View the scalable diagram inline
What this computed plan shows
For the 5kW 48V Tiny Home Solar Wiring Diagram Printable (5S2P), a 5S2P array gives 5 kW of rated panel capacity for the tiny home use case. Nameplate multiplication produces 260 Voc, 220 Vmp and 23.6 Isc at the combined array. Those values are carried forward into controller and conductor checks instead of being rounded into a one-size-fits-all diagram.
At the charge controller, the drawing records a 131 A minimum and a 325 V design Voc. Those are different questions: one protects adequate charging output, while the other keeps the 5S2P string below the equipment’s 400 V input limit. Both checks return within for this exact 5kW 48V Tiny Home Solar Wiring Diagram Printable (5S2P) state.
PV current is evaluated at 36.8 A for the 36 ft array run, which selects 8 AWG copper plus a 40 A OCPD. Charging current is 104.2 A across 10 ft, moving the recommendation to 3/0 AWG copper with 150 A protection. Each percentage in the table is a round-trip voltage-drop calculation.
Storage is drawn as 4S2P: 8 AGM units, each 120 Ah. That produces 240 Ah at 48 V and 11,520 Wh nominal. The complete-series-string rule is why the count and arrangement appear together rather than as an interchangeable battery total.
A 4,700 W continuous inverter draws about 108.8 A from this 48 V bank under the stated efficiency assumption. The 6 ft feed therefore becomes 3/0 AWG copper, protected at 150 A and calculated at 0.21% drop. Keeping this high-current run short is usually more effective than buying around a poor layout.
All three schedule rows pass the shared ampacity and voltage-drop checks for the inputs printed here. That does not account for every field condition, including conduit fill, grouped conductors, engine-room heat, corrosion exposure or manufacturer-specific terminal limits. Treat the 5kW 48V Tiny Home Solar Wiring Diagram Printable (5S2P) as a traceable calculation snapshot and have work reviewed whenever the installation falls outside its displayed assumptions.
For later comparison, keep the 5 kW array, 4S2P bank and the 36/10/6 ft one-way routes together when requesting equipment quotes or an inspection review.
Wire, protection and battery schedules
Wire schedule
| Segment | Design current | One-way run | Computed conductor | Voltage drop | Sizing basis |
|---|---|---|---|---|---|
| array → controller | 36.8 A | 36 ft | 8 AWG copper | 0.94% | 156% of array Isc (NEC 690.8) |
| controller → battery | 104.2 A | 10 ft | 3/0 AWG copper | 0.33% | controller output at 125% continuous-load ampacity |
| battery → inverter | 108.8 A | 6 ft | 3/0 AWG copper | 0.21% | inverter continuous DC input at 90% efficiency and 125% ampacity |
Overcurrent protection
| Protected segment | Required ampacity | OCPD | Conductor ampacity | Verdict |
|---|---|---|---|---|
| array → controller | 36.8 A | 40 A | 40 A | within |
| controller → battery | 130.2 A | 150 A | 165 A | within |
| battery → inverter | 136 A | 150 A | 165 A | within |
Battery arrangement
| Arrangement | Chemistry | Units | Unit capacity | Bank capacity | Nominal energy | Nominal voltage |
|---|---|---|---|---|---|---|
| 4S2P | AGM | 8 | 120 Ah | 240 Ah | 11,520 Wh | 48 V |
Static routed parts list
Parts are computed from this passing configuration. A route appears only when the verified catalogue record proves every displayed numeric rating; all uncertain matches stay local for verification. Routed links may earn Off Grid Authority a commission at no extra cost to you.
Pre-install review steps
- Confirm the array and controller window: Verify that the 5S2P string plan produces 260 V open circuit and that the equipment is rated above the 325 V cold-design value.
- Lay out the protected DC runs: Measure the one-way paths before ordering cable, then compare them with the computed 36 ft, 10 ft and 6 ft runs shown here.
- Build complete battery strings: Arrange all 8 battery units as 4S2P; do not leave a partial series string in a 48 V bank.
- Commission against equipment instructions: Check polarity, terminal torque, DC interrupt ratings, conductor temperature ratings, ambient correction and local inspection requirements before energizing the 4,700 W inverter.
Customize or compare
Open the parent build guide for the surrounding design context, safety notes and installation discussion.