3kW 48V RV Solar Wiring Diagram Printable (4S2P)
Computed 3kW 48V rv / camper solar diagram: 4S2P array, wire gauges, OCPD, battery arrangement, routed parts and printable files.
View the scalable diagram inline
What this computed plan shows
Numbers, not decorative lines, define the 3kW 48V RV Solar Wiring Diagram Printable (4S2P). The 4S2P field connects 8 panels for 3 kW of nameplate power, 158 operating volts and 19.8 short-circuit amps. That combination gives a rv / camper builder a concrete starting case that can be changed in the linked customizer.
Controller sizing follows two separate limits in this rv / camper configuration. Power conversion calls for 79 A or more at the battery side, and cold-array allowance raises the PV check from 190 V nameplate Voc to 237.5 V. The selected MPPT envelope is 90 A and 300 V.
The array-to-controller route is 32 ft one way and carries 30.9 design amps. It resolves to 8 AWG copper, a 35 A OCPD and 0.97% calculated drop. Downstream, the 4 ft controller lead uses 3 AWG copper behind 80 A protection, holding its computed drop to 0.26%.
For storage, the computed arrangement is 4S2P, assembled from 8 × 120 Ah AGM batteries. Series connection establishes the 48 V nominal level, while parallel strings bring the bank to 240 Ah. The displayed 11,520 Wh is nominal capacity rather than a promise of daily usable energy.
The inverter contributes 69.4 A of continuous DC input at the engine’s efficiency assumption. Over a 5 ft one-way cable path, 2 AWG copper and a 90 A protective device keep calculated drop at 0.28%. Its 6,000 W surge label is recorded for equipment comparison, but the schedule must still be checked against the chosen inverter manual.
This page stays inside the verified engine boundary: every component and conductor currently returns a within verdict. A different panel label, longer run, hotter ambient or changed battery count can alter that result, so follow the customize link rather than scaling the picture by intuition. Local rules, equipment listings and inspection requirements take precedence over this planning aid.
For later comparison, keep the 3 kW array, 4S2P bank and the 32/4/5 ft one-way routes together when requesting equipment quotes or an inspection review.
Wire, protection and battery schedules
Wire schedule
| Segment | Design current | One-way run | Computed conductor | Voltage drop | Sizing basis |
|---|---|---|---|---|---|
| array → controller | 30.9 A | 32 ft | 8 AWG copper | 0.97% | 156% of array Isc (NEC 690.8) |
| controller → battery | 62.5 A | 4 ft | 3 AWG copper | 0.26% | controller output at 125% continuous-load ampacity |
| battery → inverter | 69.4 A | 5 ft | 2 AWG copper | 0.28% | inverter continuous DC input at 90% efficiency and 125% ampacity |
Overcurrent protection
| Protected segment | Required ampacity | OCPD | Conductor ampacity | Verdict |
|---|---|---|---|---|
| array → controller | 30.9 A | 35 A | 40 A | within |
| controller → battery | 78.1 A | 80 A | 85 A | within |
| battery → inverter | 86.8 A | 90 A | 95 A | within |
Battery arrangement
| Arrangement | Chemistry | Units | Unit capacity | Bank capacity | Nominal energy | Nominal voltage |
|---|---|---|---|---|---|---|
| 4S2P | AGM | 8 | 120 Ah | 240 Ah | 11,520 Wh | 48 V |
Static routed parts list
Parts are computed from this passing configuration. A route appears only when the verified catalogue record proves every displayed numeric rating; all uncertain matches stay local for verification. Routed links may earn Off Grid Authority a commission at no extra cost to you.
Pre-install review steps
- Confirm the array and controller window: Verify that the 4S2P string plan produces 190 V open circuit and that the equipment is rated above the 237.5 V cold-design value.
- Lay out the protected DC runs: Measure the one-way paths before ordering cable, then compare them with the computed 32 ft, 4 ft and 5 ft runs shown here.
- Build complete battery strings: Arrange all 8 battery units as 4S2P; do not leave a partial series string in a 48 V bank.
- Commission against equipment instructions: Check polarity, terminal torque, DC interrupt ratings, conductor temperature ratings, ambient correction and local inspection requirements before energizing the 3,000 W inverter.
Customize or compare
Open the parent build guide for the surrounding design context, safety notes and installation discussion.