900W 48V Well-Pump Solar Wiring Diagram Printable (3S1P)
Computed 900W 48V well pump solar diagram: 3S1P array, wire gauges, OCPD, battery arrangement, routed parts and printable files.
View the scalable diagram inline
What this computed plan shows
Numbers, not decorative lines, define the 900W 48V Well-Pump Solar Wiring Diagram Printable (3S1P). The 3S1P field connects 3 panels for 900 W of nameplate power, 93 operating volts and 10.1 short-circuit amps. That combination gives a well pump builder a concrete starting case that can be changed in the linked customizer.
Controller sizing follows two separate limits in this well pump configuration. Power conversion calls for 24 A or more at the battery side, and cold-array allowance raises the PV check from 112.5 V nameplate Voc to 140.6 V. The selected MPPT envelope is 40 A and 200 V.
On the first two protected runs, the schedule pairs 20 A with 12 AWG copper and 25 A with 10 AWG copper. The corresponding one-way distances are 29 ft and 6 ft, producing 1.95% and 0.58% drop. These values assume the stated conductor material and do not include unverified ambient or bundling derates.
For storage, the computed arrangement is 4S3P, assembled from 12 × 200 Ah AGM batteries. Series connection establishes the 48 V nominal level, while parallel strings bring the bank to 600 Ah. The displayed 28,800 Wh is nominal capacity rather than a promise of daily usable energy.
The inverter contributes 69.4 A of continuous DC input at the engine’s efficiency assumption. Over a 5 ft one-way cable path, 2 AWG copper and a 90 A protective device keep calculated drop at 0.28%. Its 6,000 W surge label is recorded for equipment comparison, but the schedule must still be checked against the chosen inverter manual.
This page stays inside the verified engine boundary: every component and conductor currently returns a within verdict. A different panel label, longer run, hotter ambient or changed battery count can alter that result, so follow the customize link rather than scaling the picture by intuition. Local rules, equipment listings and inspection requirements take precedence over this planning aid.
For later comparison, keep the 900 W array, 4S3P bank and the 29/6/5 ft one-way routes together when requesting equipment quotes or an inspection review.
Wire, protection and battery schedules
Wire schedule
| Segment | Design current | One-way run | Computed conductor | Voltage drop | Sizing basis |
|---|---|---|---|---|---|
| array → controller | 15.8 A | 29 ft | 12 AWG copper | 1.95% | 156% of array Isc (NEC 690.8) |
| controller → battery | 18.8 A | 6 ft | 10 AWG copper | 0.58% | controller output at 125% continuous-load ampacity |
| battery → inverter | 69.4 A | 5 ft | 2 AWG copper | 0.28% | inverter continuous DC input at 90% efficiency and 125% ampacity |
Overcurrent protection
| Protected segment | Required ampacity | OCPD | Conductor ampacity | Verdict |
|---|---|---|---|---|
| array → controller | 15.8 A | 20 A | 20 A | within |
| controller → battery | 23.4 A | 25 A | 30 A | within |
| battery → inverter | 86.8 A | 90 A | 95 A | within |
Battery arrangement
| Arrangement | Chemistry | Units | Unit capacity | Bank capacity | Nominal energy | Nominal voltage |
|---|---|---|---|---|---|---|
| 4S3P | AGM | 12 | 200 Ah | 600 Ah | 28,800 Wh | 48 V |
Static routed parts list
Parts are computed from this passing configuration. A route appears only when the verified catalogue record proves every displayed numeric rating; all uncertain matches stay local for verification. Routed links may earn Off Grid Authority a commission at no extra cost to you.
Pre-install review steps
- Confirm the array and controller window: Verify that the 3S1P string plan produces 112.5 V open circuit and that the equipment is rated above the 140.6 V cold-design value.
- Lay out the protected DC runs: Measure the one-way paths before ordering cable, then compare them with the computed 29 ft, 6 ft and 5 ft runs shown here.
- Build complete battery strings: Arrange all 12 battery units as 4S3P; do not leave a partial series string in a 48 V bank.
- Commission against equipment instructions: Check polarity, terminal torque, DC interrupt ratings, conductor temperature ratings, ambient correction and local inspection requirements before energizing the 3,000 W inverter.
Customize or compare
Open the parent build guide for the surrounding design context, safety notes and installation discussion.